Reply To: Plaster Orgonite

Forum Forum OrgonitePlus Forum Josh Plaster Orgonite Reply To: Plaster Orgonite

#52

Re: Plaster orgonite
by Steve on Sun Jun 27, 2010 2:35 pm
Hi MG, I get about a 26% increase in power with the piece wrapped with elec cord.
Josh I’m getting about 440,000 on that one. The main thing is these pieces are feeding the orgone back into the grid.
Peace
Steve
Re: Plaster orgonite
by josh on Sun Jun 27, 2010 2:37 pm
Steve, my lady is asking; if she color that large piece will the energy rise significantly
josh
Re: Plaster orgonite
by Steve on Sun Jun 27, 2010 3:22 pm
I’m getting that the energy stays about the same but the freq could change based on color choice.
S
Steve
Re: Plaster orgonite
by monsoon gecko on Mon Jun 28, 2010 7:50 am
Yo…Steve, this is just great information…great confirmation boost
for experimenters….I’ll be making more plaster broadcasters…..
that’s for sure,,, Thanks
monsoon gecko
Re: Plaster orgonite
by Spirit Walker on Thu Jul 01, 2010 9:15 pm
IMG_0001.JPG
You do not have the required permissions to view the files attached to this post.
Spirit Walker
Re: Plaster orgonite
by MariaT on Thu Jul 01, 2010 9:22 pm
Hi Josh… thanks for a fascinating thread. I’m a new member who found your site a couple of days ago and became enthralled by plasterite. I’ve only been making orgonite since August 2009 and although I still have lots to learn, I’m passionate about it.
I live in Cape Town and had intended making an orgonite CB for an event scheduled for 25 July, the Golden Pyramid of Peace. However, I’m having difficulty in finding DT crystals of the correct size. A trip to my normal supplier a few days ago proved to be unsuccessful, as did enquiries from other local suppliers.
I’ve now decided to make a plasterite cone instead for the event! Thanks to you.
So yesterday I collected plaster of paris and some oxide. Can’t find copper powder yet in small quantities (I was quoted R666 – about $88 – for 1kg!!). Is it OK to use copper sulphate instead? I’ve decided to use my newly acquired stainless steel pyramid mould which I’ve only used twice – and both orgonite pieces cracked horribly! It just generates too much heat, lol. The pyramid mould is only about 100mm high, though. I’m a bit rushed for time right now (preparing for 2 holistic fairs over the next 10 days) but I’d like to find a long cone mould as soon as possible.
So… once again thank you for this forum, and thanks to all members that have contributed.
MariaT
Re: Plaster orgonite
by Spirit Walker on Thu Jul 01, 2010 9:45 pm
Just a couple of the latest test casts from various “molds”…
You do not have the required permissions to view the files attached to this post.
Spirit Walker
 
Re: Plaster orgonite
by Spirit Walker on Thu Jul 01, 2010 9:58 pm
I just handed these individually to my daughter after taking the photos, and her expressions and comments were priceless. Starting with smallest, her eyes got huge and she immediately said shocks in her hand. With second bowl piece, a vibration and a look of confusion. The third largest, amazement, and she gushed and blushed, said Wow. hole body got warm.   Will share mix ingredients, with Josh’s permission, later to any who wish… All pieces are unusually “cold” when holding, almost like putting your hand against a cool marble wall at a fancy hotel. The largest piece is the coldest, done right chilly to hold. I stacked them from smallest to largest, and there was 3 loud knocks on the wall immediately after ward, within a split second, right next to me on the bed. I jumped. Took the top piece off, felt the air pressure in room change. Put it back on, heard the 3 knocks again!!! I tried to take a picture of it, my camera batteries went dead. Replaced them, snapped the pic, camera shut off! Retried four times, same thing happened. Fifth time checked battery level, almost exhausted. New batteries out of the pack…   Too funny. So no pics of stack, but I promise it was entertaining!
Aho!
Tony